View AT90S2313_254157.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* AVR(R) - High Performance and Low Power RISC Architecture * 118 Powerful Instructions - Most Single Clock Cycle Execution * 2K bytes of In-System Reprogrammable Flash * * * * * * * * * * * * * * * * *
- SPI Serial Interface for Program Downloading - Endurance: 1,000 Write/Erase Cycles 128 bytes EEPROM - Endurance: 100,000 Write/Erase Cycles 128 bytes Internal RAM 32 x 8 General Purpose Working Registers 15 Programmable I/O Lines VCC: 2.7 - 6.0V Fully Static Operation - 0 - 10 MHz, 4.0 - 6.0V - 0 - 4 MHz, 2.7 - 6.0V Up to 10 MIPS Throughput at 10 MHz One 8-Bit Timer/Counter with Separate Prescaler One 16-Bit Timer/Counter with Separate Prescaler and Compare and Capture Modes Full Duplex UART Selectable 8, 9 or 10 bit PWM External and Internal Interrupt Sources Programmable Watchdog Timer with On-Chip Oscillator On-Chip Analog Comparator Low Power Idle and Power Down Modes Programming Lock for Software Security 20-Pin Device
8-Bit Microcontroller with 2K bytes In-System Programmable Flash AT90S2313
Description
The AT90S2313 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the AT90S2313 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed. The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. (continued)
Pin Configuration
Rev. 0839DS-07/98
Note: This is a summary document. For the complete 68 page datasheet, please visit our web site at www.atmel.com or e1 mail at literature@atmel.com and request literature #0839D.
Block Diagram
Figure 1. The AT90S2313 Block Diagram
The AT90S2313 provides the following features: 2K bytes of In-System Programmable Flash, 128 bytes EEPROM, 128 bytes SRAM, 15 general purpose I/O lines, 32 general purpose working registers, flexible timer/counters with compare modes, internal and external interrupts, a programmable serial UART, programmable Watchdog Timer with internal oscillator, an SPI serial port for Flash Memory downloading and two software selectable power saving modes. The Idle Mode stops the CPU while allowing the SRAM, timer/counters, SPI port and interrupt system to continue functioning. The power down mode saves the register contents but freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset. The device is manufactured using Atmel's high density non-volatile memory technology. The on-chip In-System
Programmable Flash allows the program memory to be reprogrammed in-system through an SPI serial interface or by a conventional nonvolatile memory programmer. By combining an enhanced RISC 8-bit CPU with In-System Programmable Flash on a monolithic chip, the Atmel AT90S2313 is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The AT90S2313 AVR is supported with a full suite of program and system development tools including: C compilers, macro assemblers, program debugger/simulators, incircuit emulators, and evaluation kits.
2
AT90S2313
AT90S2313
Pin Descriptions
VCC Supply voltage pin. GND Ground pin. Port B (PB7..PB0) Port B is an 8-bit bi-directional I/O port. Port pins can provide internal pull-up resistors (selected for each bit). PB0 and PB1 also serve as the positive input (AIN0) and the negative input (AIN1), respectively, of the on-chip analog comparator. The Port B output buffers can sink 20mA and can drive LED displays directly. When pins PB0 to PB7 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. Port B also serves the functions of various special features of the AT90S2313 as listed on page 38. Port D (PD6..PD0) Port D has seven bi-directional I/O pins with internal pull-up resistors, PD6..PD0. The Port D output buffers can sink 20 mA. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. Port D also serves the functions of various special features of the AT90S2313 as listed on page 43. RESET Reset input. A low on this pin for two machine cycles while the oscillator is running resets the device. XTAL1 Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XTAL2 Output from the inverting oscillator amplifier Figure 2. Oscillator Connections
Figure 3. External Clock Drive Configuration
Crystal Oscillator
XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 2. Either a quartz crystal or a ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 3.
3
AT90S2313 Architectural Overview
The fast-access register file concept contains 32 x 8-bit general purpose working registers with a single clock cycle access time. This means that during one single clock cycle, one ALU (Arithmetic Logic Unit) operation is executed. Two operands are output from the register file, the operation is executed, and the result is stored back in the register file in one clock cycle. Six of the 32 registers can be used as three 16-bits indirect address register pointers for Data Space addressing enabling efficient address calculations. One of the three address pointers is also used as the address pointer for the constant table look up function. These added function registers are the 16-bits X-register, Y-register and Z-register. The ALU supports arithmetic and logic functions between registers or between a constant and a register. Single register operations are also executed in the ALU. Figure 4 shows the AT90S2313 AVR Enhanced RISC microcontroller architecture. In addition to the register operation, the conventional memory addressing modes can be used on the register file as well. This is enabled by the fact that the register file is assigned the 32 lowermost Data Space addresses ($00 $1F), allowing them to be accessed as though they were ordinary memory locations. The I/O memory space contains 64 addresses for CPU peripheral functions as Control Registers, Timer/Counters, A/D-converters, and other I/O functions. The I/O memory can be accessed directly, or as the Data Space locations following those of the register file, $20 - $5F. The AVR has Harvard architecture - with separate memories and buses for program and data. The program memory is accessed with a two stage pipeline. While one instruction is being executed, the next instruction is pre-fetched from the program memory. This concept enables instructions to be executed in every clock cycle. The program memory is In-system Programmable Flash memory. With the relative jump and call instructions, the whole 1K address space is directly accessed. Most AVR instructions have a single 16-bit word format. Every program memory address contains a 16- or 32-bit instruction. During interrupts and subroutine calls, the return address program counter (PC) is stored on the stack. The stack is effectively allocated in the general data SRAM, and consequently the stack size is only limited by the total SRAM size and the usage of the SRAM. All user programs must initialize the SP in the reset routine (before subroutines or interrupts are executed). The 8-bit stack pointer SP is read/write accessible in the I/O space. The 128 bytes data SRAM + register file and I/O registers can be easily accessed through the five different addressing modes supported in the AVR architecture. The memory spaces in the AVR architecture are all linear and regular memory maps.
4
AT90S2313
AT90S2313
Figure 4. The AT90S2313 AVR Enhanced RISC Architecture
Figure 5. Memory Maps
5
AT90S2313 Register Summary
Address
$3F ($5F) $3E ($5E) $3D ($5D) $3C ($5C) $3B ($5B) $3A ($5A) $39 ($59) $38 ($58) $37 ($57) $36 ($56) $35 ($55) $34 ($54) $33 ($53) $32 ($52) $31 ($51) $30 ($50) $2F ($4F) $2E ($4E) $2D ($4D) $2C ($4C) $2B ($4B) $2A ($4A) $29 ($49) $28 ($48) $27 ($47) $26 ($46) $25 ($45) $24 ($44) $23 ($43) $22 ($42) $21 ($41) $20 ($40) $1F ($3F) $1E ($3E) $1D ($3D) $1C ($3C) $1B ($3B) $1A ($3A) $19 ($39) $18 ($38) $17 ($37) $16 ($36) $15 ($35) $14 ($34) $13 ($33) $12 ($32) $11 ($31) $10 ($30) $0F ($2F) $0E ($2E) $0D ($2D) $0C ($2C) $0B ($2B) $0A ($2A) $09 ($29) $08 ($28) ... $00 ($20)
Name
SREG Reserved SPL Reserved GIMSK GIFR TIMSK TIFR Reserved Reserved MCUCR Reserved TCCR0 TCNT0 Reserved Reserved TCCR1A TCCR1B TCNT1H TCNT1L OCR1AH OCR1AL Reserved Reserved Reserved Reserved ICR1H ICR1L Reserved Reserved WDTCR Reserved Reserved EEAR EEDR EECR Reserved Reserved Reserved PORTB DDRB PINB Reserved Reserved Reserved PORTD DDRD PIND Reserved Reserved Reserved UDR USR UCR UBRR ACSR Reserved Reserved
Bit 7
I SP7 INT1 INTF1 TOIE1 TOV1
Bit 6
T SP6 INT0 INTF0 OCIE1A OCF1A
Bit 5
H SP5 -
Bit 4
S SP4 -
Bit 3
V SP3 TICIE1 ICF1
Bit 2
N SP2 -
Bit 1
Z SP1 TOIE0 TOV0
Bit 0
C SP0 -
Page
17 18 23 23 23 24
-
-
SE -
SM -
ISC11 -
ISC10 CS02
ISC01 CS01
ISC00 CS00
25 28 29
Timer/Counter0 (8 Bit)
COM1A1 COM1A0 ICNC1 ICES1 . Timer/Counter1 - Counter Register High Byte Timer/Counter1 - Counter Register Low Byte Timer/Counter1 - Compare Register High Byte Timer/Counter1 - Compare Register Low Byte
CTC1
CS12
PWM11 CS11
PWM10 CS10
30 31 32 32 32 32
Timer/Counter1 - Input Capture Register High Byte Timer/Counter1 - Input Capture Register Low Byte
33 33
-
-
-
WDTOE
WDE
WDP2
WDP1
WDP0
35
EEPROM Address Register EEPROM Data register -
-
-
EEMWE
EEWE
EERE
36 37 37
PORTB7 DDB7 PINB7
PORTB6 DDB6 PINB6
PORTB5 DDB5 PINB5
PORTB4 DDB4 PINB4
PORTB3 DDB3 PINB3
PORTB2 DDB2 PINB2
PORTB1 DDB1 PINB1
PORTB0 DDB0 PINB0
46 46 46
-
PORTD6 DDD6 PIND6
PORTD5 DDD5 PIND5
PORTD4 DDD4 PIND4
PORTD3 DDD3 PIND3
PORTD2 DDD2 PIND2
PORTD1 DDD1 PIND1
PORTD0 DDD0 PIND0
51 51 51
UART I/O Data Register RXC TXC UDRE RXCIE TXCIE UDRIE UART Baud Rate Register ACD ACO
FE RXEN ACI
OR TXEN ACIE
CHR9 ACIC
RXB8 ACIS1
TXB8 ACIS0
40 40 41 43 44
6
AT90S2313
AT90S2313
AT90S2313 Instruction Set Summary
Mnemonics Operands Description Operation
Rd Rd + Rr Rd Rd + Rr + C Rdh:Rdl Rdh:Rdl + K Rd Rd - Rr Rd Rd - K Rdh:Rdl Rdh:Rdl - K Rd Rd - Rr - C Rd Rd - K - C Rd Rd * Rr Rd Rd * K Rd Rd v Rr Rd Rd v K Rd Rd Rr Rd $FF - Rd Rd $00 - Rd Rd Rd v K Rd Rd * ($FF - K) Rd Rd + 1 Rd Rd - 1 Rd Rd * Rd Rd Rd Rd Rd $FF PC PC + k + 1 PC Z PC PC + k + 1 PC Z PC STACK PC STACK if (Rd = Rr) PC PC + 2 or 3
Flags
Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,C,N,V,H Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,C,N,V Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V None None None None None None I None Z, N,V,C,H Z, N,V,C,H Z, N,V,C,H None None None None None None None None None None None None None None None None None None None None None None None None
#Clocks
1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 3 3 4 4 1/2 1 1 1 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers ADC Rd, Rr Add with Carry two Registers ADIW Rdl,K Add Immediate to Word SUB Rd, Rr Subtract two Registers SUBI Rd, K Subtract Constant from Register SBIW Rdl,K Subtract Immediate from Word SBC Rd, Rr Subtract with Carry two Registers SBCI Rd, K Subtract with Carry Constant from Reg. AND Rd, Rr Logical AND Registers ANDI Rd, K Logical AND Register and Constant OR Rd, Rr Logical OR Registers ORI Rd, K Logical OR Register and Constant EOR Rd, Rr Exclusive OR Registers COM Rd One's Complement NEG Rd Two's Complement SBR Rd,K Set Bit(s) in Register CBR Rd,K Clear Bit(s) in Register INC Rd Increment DEC Rd Decrement TST Rd Test for Zero or Minus CLR Rd Clear Register SER Rd Set Register BRANCH INSTRUCTIONS RJMP k Relative Jump IJMP Indirect Jump to (Z) RCALL k Relative Subroutine Call ICALL Indirect Call to (Z) RET Subroutine Return RETI Interrupt Return CPSE Rd,Rr Compare, Skip if Equal CP Rd,Rr Compare CPC Rd,Rr Compare with Carry CPI Rd,K Compare Register with Immediate SBRC Rr, b Skip if Bit in Register Cleared SBRS Rr, b Skip if Bit in Register is Set SBIC P, b Skip if Bit in I/O Register Cleared SBIS P, b Skip if Bit in I/O Register is Set BRBS s, k Branch if Status Flag Set BRBC s, k Branch if Status Flag Cleared BREQ k Branch if Equal BRNE k Branch if Not Equal BRCS k Branch if Carry Set BRCC k Branch if Carry Cleared BRSH k Branch if Same or Higher BRLO k Branch if Lower BRMI k Branch if Minus BRPL k Branch if Plus BRGE k Branch if Greater or Equal, Signed BRLT k Branch if Less Than Zero, Signed BRHS k Branch if Half Carry Flag Set BRHC k Branch if Half Carry Flag Cleared BRTS k Branch if T Flag Set BRTC k Branch if T Flag Cleared BRVS k Branch if Overflow Flag is Set BRVC k Branch if Overflow Flag is Cleared BRIE k Branch if Interrupt Enabled BRID k Branch if Interrupt Disabled
Rd - Rr Rd - Rr - C Rd - K
if (Rr(b)=0) PC PC + 2 or 3 if (Rr(b)=1) PC PC + 2 or 3 if (P(b)=0) PC PC + 2 or 3 if (R(b)=1) PC PC + 2 or 3 if (SREG(s) = 1) then PCPC + k + 1 if (SREG(s) = 0) then PCPC + k + 1 if (Z = 1) then PC PC + k + 1 if (Z = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (N = 1) then PC PC + k + 1 if (N = 0) then PC PC + k + 1 if (N V= 0) then PC PC + k + 1 if (N V= 1) then PC PC + k + 1 if (H = 1) then PC PC + k + 1 if (H = 0) then PC PC + k + 1 if (T = 1) then PC PC + k + 1 if (T = 0) then PC PC + k + 1 if (V = 1) then PC PC + k + 1 if (V = 0) then PC PC + k + 1 if (I = 1) then PC PC + k + 1 if (I = 0) then PC PC + k + 1
7
Mnemonics
Operands
Description
Move Between Registers Load Immediate Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Direct from SRAM Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Direct to SRAM Load Program Memory In Port Out Port Push Register on Stack Pop Register from Stack Set Bit in I/O Register Clear Bit in I/O Register Logical Shift Left Logical Shift Right Rotate Left Through Carry Rotate Right Through Carry Arithmetic Shift Right Swap Nibbles Flag Set Flag Clear Bit Store from Register to T Bit load from T to Register Set Carry Clear Carry Set Negative Flag Clear Negative Flag Set Zero Flag Clear Zero Flag Global Interrupt Enable Global Interrupt Disable Set Signed Test Flag Clear Signed Test Flag Set Twos Complement Overflow Clear Twos Complement Overflow Set T in SREG Clear T in SREG Set Half Carry Flag in SREG Clear Half Carry Flag in SREG No Operation Sleep Watchdog Reset
Operation
Rd Rr Rd K Rd (X) Rd (X), X X + 1 X X - 1, Rd (X) Rd (Y) Rd (Y), Y Y + 1 Y Y - 1, Rd (Y) Rd (Y + q) Rd (Z) Rd (Z), Z Z+1 Z Z - 1, Rd (Z) Rd (Z + q) Rd (k) (X) Rr (X) Rr, X X + 1 X X - 1, (X) Rr (Y) Rr (Y) Rr, Y Y + 1 Y Y - 1, (Y) Rr (Y + q) Rr (Z) Rr (Z) Rr, Z Z + 1 Z Z - 1, (Z) Rr (Z + q) Rr (k) Rr R0 (Z) Rd P P Rr STACK Rr Rd STACK I/O(P,b) 1 I/O(P,b) 0 Rd(n+1) Rd(n), Rd(0) 0 Rd(n) Rd(n+1), Rd(7) 0 Rd(0)C,Rd(n+1) Rd(n),CRd(7) Rd(7)C,Rd(n) Rd(n+1),CRd(0) Rd(n) Rd(n+1), n=0..6 Rd(3..0)Rd(7..4),Rd(7..4)Rd(3..0) SREG(s) 1 SREG(s) 0 T Rr(b) Rd(b) T C1 C0 N1 N0 Z1 Z0 I1 I0 S1 S0 V1 V0 T1 T0 H1 H0 (see specific descr. for Sleep function) (see specific descr. for WDR/timer)
Flags
None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V None SREG(s) SREG(s) T None C C N N Z Z I I S S V V T T H H None None None
#Clocks
1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1
DATA TRANSFER INSTRUCTIONS MOV Rd, Rr LDI Rd, K LD Rd, X LD Rd, X+ LD Rd, - X LD Rd, Y LD Rd, Y+ LD Rd, - Y LDD Rd,Y+q LD Rd, Z LD Rd, Z+ LD Rd, -Z LDD Rd, Z+q LDS Rd, k ST X, Rr ST X+, Rr ST - X, Rr ST Y, Rr ST Y+, Rr ST - Y, Rr STD Y+q,Rr ST Z, Rr ST Z+, Rr ST -Z, Rr STD Z+q,Rr STS k, Rr LPM IN Rd, P OUT P, Rr PUSH Rr POP Rd BIT AND BIT-TEST INSTRUCTIONS SBI P,b CBI P,b LSL Rd LSR Rd ROL Rd ROR Rd ASR Rd SWAP Rd BSET s BCLR s BST Rr, b BLD Rd, b SEC CLC SEN CLN SEZ CLZ SEI CLI SES CLS SEV CLV SET CLT SEH CLH NOP SLEEP WDR
8
AT90S2313

▲Up To Search▲

Price & Availability of AT90S2313

	To Download AT90S2313 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .